Analysis of Connector Mold Parts Forging Cooling Processing

   Connector mold parts forging processing from the final forging temperature cooling to room temperature is called the forging cooling process, it is one of the links in the production of forging cooling process. The connector mold parts forging cooling processing according to chemical composition, section size, raw material quality, the different cooling methods.If connector mold parts forging cooling processing is improper, light is forging deformation bending, surface hardness too high and not cutting, may also extend the production cycle; forging crack, flake is serious, the forgings. Cooling after forging of high alloy steel and large forging is very important. Forging cooling methods in common use, according to the cooling speed from fast to slow the sequence into air cooling, cooling, pit cooling (or box cold), grey(or cold), annealing furnace cooling.
  1) air cooling. The connector mold parts forging cooling processing in the shop on the ground, but not on the damp ground or metal plates, but also to prevent the draught, avoid forging cooling too fast and cracks, bending, deformation and other defects.
  2) stack cooling. The connector mold parts forging cooling processing after forging into stack cooling in still air.
  3) Keng (or cold boxcold). The connector mold parts forging cooling processing
 in the pit or in the box.
  4) grey (or cold). Yize connector mold parts forging cooling processing in the slag, lime and sand. The slag, lime or sand must be dry. General forging into slag,lime or sand temperature not lower than 500 ℃, forging around the slag, lime or sand thickness shall not be less than 80mm.
  5) furnace cooling. The connector mold parts forging cooling processing
 on slow cooling in the furnace. Forging furnace temperatureat 600~650 ℃, the minimum should not below 350 ℃. The furnace should be raised to 650 ℃ to be expected, because the temperature is favorable to the diffusion hydrogen. To be forging all into the furnace after furnace cooling by cooling specification. The general temperature not higher than 100~150 ℃. To avoid cold air into the furnace.
 6) annealing. This is to prevent the cooling heat treatment process of the white spot.

Article from above Yize Official website http://www.yizemoulds.com/， Original Address http://www.yizemoulds.com/news_show_6_28_283.html， Reproduced please specify. xiaoyunone110

Core pins And Aleeves Noble Manufacture

  With the development of core pins and sleeves development, ultra precision core pins and sleeves noble manufacture with machining technology of machining accuracy higher than 1 μ m and collector, chemistry, ultrasonic, laser technology in machining with manufacturing in the mould has broad prospects. At present, machine tool manufacturers are keen to production for high speed machining center processing and specialized design, high-speed core pins and sleeves technology in America to reduce . Core pins and sleeves noble manufacture with this technology in Europe and Japan are also popular. In addition, by using cavity mould fully hardened is another important trend in the development of mold industry. With the rapid development of various new technologies have appeared, foreign core pins and sleeves processing system, the system is made up of the rational combination of machine tools, with accompanying positioning fixture or positioning plate, complete machines, CNC tool library and CNC flexible synchronization system, a real-time quality monitoring and control system. As can be seen from the development of die and mould industry is fierce walk, believe that the future development of mold manufacturing industry will be more quickly.

Article from above Yize Official website http://www.yizemoulds.com/， Original Address http://www.yizemoulds.com/news_show_6_28_279.html， Reproduced please specify. xiaoyunone110

How to be along with the transition path in mold parts industry

   In China, how to be along with the transition path in mold parts industry? To understand the problem, China mold parts industry today, in the fierce competition in the market environment, trend of China mold parts industry production appeared Pyramid phenomenon. Firstly, the hardware mold parts industry leading role is not strong. Second, weak technological innovation ability of mold parts industry . Thirdly, mold parts industry market structure is too single, export dependence is too high.Fourth, brand construction has lagged behind, the lack of awareness and core competitiveness. Fifth, the lack of public platform service. Some of the original problems are constantly emerging, also more and more serious. For example, the low cost of mould, structure of product quality and technical content is not high, rough and so.

Article from above Yize Official website http://www.yizemoulds.com/， Original Address http://www.yizemoulds.com/news_show_6_28_275.html， Reproduced please specify. xiaoyunone110

The Development of Connector Mold Parts Technology

   The rapid development of connector mold parts technology is to rely on the development of mold industries, the development of connector mold parts technology is also promoting a small aspect of China economic development, so that the development of connector mold parts industry and the economic development of a country is closely related to.
   China connector mold parts, the productivity level after years of continuous development, the connector mold parts technology either in production or in the technology are improved, the connector mold parts in our country with high quality and inexpensive advantage is gradually to replace imported stamping die. Yize connector mold parts is on high quality and inexpensive advantage to enter foreign markets, and the long-term cooperation, Germany, Japan, Italy, America, Israel, Singapore, Thailand, Malaysia and other countries and regions. This is also on the yize mould technology gains, yize mold has been increasing in recent years to innovate the technology of connector mold parts,  so in the production of stamping mould fittings at.

Article from above Yize Official website http://www.yizemoulds.com/， Original Address http://www.yizemoulds.com/news_show_6_28_271.html， Reproduced please specify. xiaoyunone110

The Development of Precision Auto Mold Parts

  The development of precision auto mold parts demands about seven hundred billions of China automobile needs, motorcycle industry every year, but our country has a large-scale precision auto mold parts manufacturing capacity is far from enough, now covering high quality precision auto mold parts car in China.Therefore, the development of precision auto mold parts is for maximum precision auto fittings mold domestic manufacturers, improve the precision mold manufacturing capacity.
   Yize mold is the largest precision auto mold parts processing factory, precision auto mold parts is the most famous exports the highest rate of precision auto mold parts manufacturers, many customers are from all over the world.

Article from above Yize Official website http://www.yizemoulds.com/， Original Address http://www.yizemoulds.com/news_show_6_28_267.html， Reproduced please specify. xiaoyunone110

Analysis of Mold Components Processing In China

   Analysis of the mold components processing in the CNC machine tool.
   Analysis of the mold components processing, to consider the blank material and type,mold components size, dimensional accuracy and surface roughness, parts of complicated shapes, the number of parts, heat treatment, machining parts for analysis, complete the part is machined material and the shape of the blank, the tool to set scheme. Most of the connector mold parts processing factory of up to consider fully from 3 aspects:
  Step1, Technical requirements to ensure parts; to improve productivity is advantageous economy is cost-effective.
  Step2, mold components processing analysis for relationship from the machine and the mold components production batch. Generally when the mold components not too complex, batch and hinge hours, should adopt the general machine tool; when the production batch is great to use special machine; in many varieties, small batch production situation, when the parts are complex when using CNC machine tool can obtain higher economic benefits.
  Step3, precision connector mold parts some of mold design, mold accessories customized or connector, use ordinary machine may be difficult to machining, the so-called process of structural difference. But the data processing machine, can be an easy job to achieve. So in the process of CNC technology analysis parts, need to rigorously evaluate the structure process. In order to give full play to the advantages of CNC machining, the parts must be considered when designing and CNC process design of contact, surface modeling, thin wall light, complicated in structure.


Article from above Yize Official website http://www.yizemoulds.com/， Original Address http://www.yizemoulds.com/news_show_6_28_263.html， Reproduced please specify. xiaoyunone110